S-G22Q FUEL DISPENSER

S-G22Q FUEL DISPENSER

FlowMeter Type : Optional

Accuracy :±0.2%

Pressure Loss (kg/cm): Under 0.25

Motor Voltage(V) :110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage :110V/220V/380V,50Hz/60Hz

Nozzle :Auto Shut-off Nozzle

Environmental Condition :-40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter): Type LCD and Bright Backlight

Digit of Volume :0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount :0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price :0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Optional Display: Type LCD and Bright Backlight

Digit of Volume :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose: 4.5m

Weight :247kg.

Dimension(L×W×H) : 1160*560*2215(mm)

Dimension(L×W×H)Of Qty of Container : 40ft: 27

of four-piston measurement transducer The upper subassembly includes inlet and outlet of oil. The export axis stretches out of measurement transducer from the hole of upper cover unit. The middle of frame unit is a solid chamber, connecting with four cylinders mounted stainless steel bushing. There is an oblong passage on top of each cylinder, which is communicated with l fuel dispenser ower part of cylinder. These oblong passages also communicate with annular grooves related on top of frame. Four pistons mounted idler wheels are installed respectively into bushings related, connecting piston with connect fuel dispenser ing rod at same axes. Camshaft unit insert into the oblong groove in middle of connecting rod. Shaft is supported by installing hole at lower frame and valve seat. D and U bearing are mounted in the two holes. Four end covers are installed at each end of frame, of which adjusting device being installed at one end cover to regulate the moving distance of piston concerned. Adjusting device regulates the discharge of measurement transducer so as to ensure the accuracy. Distributing valve and valve seat are installed at top of frame unit. 1-Seal gasket 2-Upper cover unit/O-ring 3-Drive fork/output shaft 4-Spring\O-ring\valve cover\seal\gasket 5-Frame\distributing valve\valve seat\connecting rod\cam\cam axis 6-Piston\clamp sheet\pin 7-End cover\adjusting bolt\gasket\regulating wheel Diagram 2-21: Exploded view of four-piston measurement transducer Working principle The pressured oil coming from vapor separator or submersible pump flows into distributing valve via measurement transducer and continuously flow into relevant cylinder via the oblong passage at top of frame so as to drive piston moving. Likewise, the piston impels opposite piston through connecting rod, pressured oil flows out the outlet of upper cover via the passages at top of cylinder and then the inboard window of distributing valve. As piston move to and fro, camshaft is driven by trolley unit that making distributing valve and export axis rotation. W fuel dispenser

s.　　 Where a default value exists for a Data_Id the dispenser should set up the Data_Id s value　　 accordingly.　　5.2 Handling After a Reset or Power Off　　After a master Reset or Power Off of the dispenser the device should:　　 Send a Configuration Needed heartbeat since it cannot know if it has the correct prices.　　 Do not clear the C fuel dispenser ommunication Specification s Recipient Address Table .　　 Do not clear current historic transactions.　　 Do not unlock locked transactions.　　 Do not reset Data_Id s to their default values.　　Octo fuel dispenser ber 2005 IFSF - STANDARD FORECOURT PROTOCOL FP31_2.22　　 DISPENSER APPLICATION　　 Page: 133　　5.3 Dispenser Behaviour after an Acknowledgement of a Command　　When a dispenser receives a command from the CD (i.e. Open_FP Close_FP Release_FP　　etc.) and the dispenser acknowledges the command positively (i.e. with a MS_ACK=0). The　　dispenser must change to the new state immediately before sending the Acknowledge reply.　　Please see the diagramexample below showing the required steps.　　 (d) Unsolicited　　 Status　　 (a) Open_FP (c) ACK　　Event　　 (b) Process Open_FP　　 Closed Open　　FP_State　　Time　　Where: a = Open_FP command sent by the Control Device.　　 b = Dispenser validates and processed the Open_FP command and decides　　 that the FP can be opened. Dispenser changes its state to Open .　　 c = Dispenser Replies to the Open_FP command by sending a positive　　 acknowledgement.　　 fuel dispenser

eged children—and Princeton rapidly followed suit. But the wind is going to have to blow a heck of a lot harder, and for a heck of a lot longer, before America s money-addicted and legacy-loving universities can be shamed into returning to what ought to have been their guiding principle all along admitting people to university on the basis of their intellectual ability fuel dispenser . © 2006 .  About sponsorship Mexico s presidential election The left cannot hold Sep 21st 2006 | MEXICO CITY From The Economist print editi fuel dispenser on Mr López Obrador s campaign of “civil resistance�starts to fizzle “THE worst are full of passionate intensity,�W.B. Yeats declared of religious zealots. The same might be said of Andrés Manuel López Obrador who, nearly three months after Mexico s presidential contest, still refuses to accept that he lost. On September 16th, Mexico City s former left-wing mayor declared himself president-elect and vowed to set up a rival government to that of Felipe Calderón, victorious candidate of President Vicente Fox s National Action Party (PAN). Mr Calderón was officially proclaimed the election winner by the federal electoral tribunal on September 5th after a series of legal challenges and a partial recount that put him just 233,831 votes ahead. Mr López Obrador s defiant proclamation came at a “National Democratic Convention� a gathering of supporters he had called in capital s central square, the Zócalo, on Mexico s independence day. He had predicted that around 1m would attend. In the event, the crowd was about the same size as his margin of loss in the election—substantially smaller than the numbers he had been attracting to his earlier rallies throughout the summer. Strangely, for someone who had mounted his campaign of “civil resistance�in protest against alleged counting inaccuracies in the presidential vote, his own “election�along with other votes by the co fuel dispenser