S-GAQ FUEL DISPENSER

S-GAQ FUEL DISPENSER

FlowMeter Type: Optional

Accuracy : ±0.2%

Pressure Loss (kg/cm): Under 0.25

Motor Voltage(V): 110V/220V/380V,50Hz/60Hz

Capacity(hp) :1HP(0.75kw)

Input Voltage : 110V/220V/380V,50Hz/60Hz

Nozzle : Auto Shut-off Nozzle

Environmental Condition: : -40~~+55degree

Control Type : Solenold Vale Control Type

Preset : Function Provided(Small LCDIndicator)

Display(Counter) :Type LCD and Bright Backlight

Digit of Volume :0~~999,999(6 Digits),Decimal point can be changed

Digit of Amount : 0~~999,999(6 Digits),Decimal point can be changed

Digit of Unit price : 0~~9999(4 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Optional Display: Type LCD and Bright Backlight

Digit of Volume :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Amount :0~~99,999,999(8 Digits),Decimal point can be changed

Digit of Unit price : 0~~999999(6 Digits),Decimal point can be changed

Digit of Total Range : 0~~99,999,999,99

Totalizer :1~~9,999,999

Hose: 4.5m

Weight : 285kg.

Dimension(L×W×H) : 1160*560*2215(mm)

Dimension(L×W×H)Of Qty of Container :40ft: 27

mp will decrease and overflow valve cut down flowage passed. When need to decrease flow rate, one will reduce openness of nozzle so as to increase the outlet pressure of pump. In that case, openness of valve and returned oil increase due to overflow valve work on spring, the outlet flowage of fuel dispenser is lessened. When the pressure of hydraulic system in fuel dispenser is suddenly increased due to some cause, overflow valve overcome spring strength under high pressure, raise openness and returned oil flowage to reduce pump pressure and protect the hydraulic system. Clockwise turn adjusting bolt of overflow valve given the openness of nozzle is unchanged the flux of fuel dispenser will be increased; anticlockwise turn decrease flux. Performance of vane pump fuel dispenser Suction capacity Like other pump the good performance of vane pump should has high suction capacity, excellent stability with less vibration, small transitional volume, low noise, nice reliability and maintainable. These traits depend upon rational structure desig fuel dispenser n, right selection of material and manufacturing level. User’s correct usage and maintenance is very important as well. Vane pump suction capacity mainly lies in the two aspects: suction distance and avoidance of air pocket. Diagram 2-5 is about pump, explaining pump suction distance. Suction distance refers to fuel dispenser’s capacity to suck oil from a certain vertical and horizontal distance, often meaning vertical distance. Keeping suction distance a definite vacuum pressure in pump inlet is prerequisite. When the oil level is high or low in tank pump inlet vacuum pressure is often high. Under such high pressure, overflow valve overcome spring strength increase openness and returned oil. Due to the pressure returned oil in other penetrative section is also increased, the filling flux is cut down consequently. The outlet flux of fuel dispenser becomes zero when returned oil reaches a certain volume. Therefore, when the returned oil of overflow valve and other penetrative s fuel dispenser

t before entering the　　 authorisation e.g. a code and a value of 1 means the authorisation e.g. a code　　 is necessary before the vehicle is positioned (this is the case when a door needs to be　　 opened).　　 The four combinations are described below with resepct to the customer displayed　　 text messages on the authorisation man machine interface (e.g. the CED) and the　　 state changes of the CWP.　　5.5.1 Automatic Start Vehicle Positioned First Mode 1A　　 StandAloneAuthorisation = 0 CodeVehicleOrder =0.　　 1. Authorisation Display: Please drive in　　 After the vehicle is in position the st fuel dispenser ate change 3 - 4 is performed　　 2. Authoristaion Display: Please enter code　　Version 1.33 IFSF - STANDARD FORECOURT PROTOCOL September 2005　　 CAR WASH SPECIFIC fuel dispenser ATION　　Page: 60 of 65　　 After the valid authorisation is entered the CD sends release command to CW　　 and CW changes its status 4 - 6　　 3. Authorisation Display: Please wait for the washing end　　5.5.2 Manual Start Vehicle Positioned First Mode 1B　　 StandAloneAuthorisation = 1 CodeVehicleOrder =0.　　 1. Authorisation Display: Please drive in　　 After the vehicle is in position the state change 3 - 4 is performed　　 2. Authorisation Display: Please enter code　　 After the valid authorisation is entered the CD sends release command to CW　　 and CW changes its status 4 - 5　　 3. Authorisation Display: Please press the START button　　 CW waits for pressing of the START button (or CD start command) then checks　　 all the internal conditions and fuel dispenser

Previous print editions Subscribe On the cover Country Briefings The world s most impressive Jun 10th 2006 Subscribe to the print edition economic machine needs a Jun 3rd 2006 Or buy a Web subscription for little adjusting leader May 27th 2006 Audio interviews fuel dispenser full access online May 20th 2006 fuel dispenser RSS feeds May 13th 2006 Classifieds Receive this page by RSS feed More print editions and PRINT EDITION covers » The world this week Politics this week Business this week A survey of logistics Leaders fuel dispenser